We narrowed to 918 results for: IRE

... in 1.5 mL microfuge tubes at 10,000 rpm would require a tabletop microcentrifuge like the one in the ... you are working. Even if your samples may not require specific PPE, you never know what else has been...RPM), these are not the same units and are not directly interchangeable. If you need to convert between...supernatant. Depending on your experiment, you may be required to save the pellet, the supernatant, or both. ...

...bottle may explode!) and then loosely cover the entire top of the bottle with aluminum foil. Autoclave...shaking incubator. Note: Some plasmids or strains require growth at 30 °C. If so, you will likely need to...in the media (Figure 1). Notes: Some protocols require bacteria to be in the log phase of growth. Check...bacteria incubated at 30 °C rather than 37 °C often require longer incubation times. Double check that the ...

...cell lines and selection markers. Note this assay requires staining resistant colonies with crystal violet...colony formation assay, the dose of antibiotic required to kill your target cell line needs to be empirically...minimum concentration (Link opens in a new window) required to kill all of the cells. Use this dose for the...cell suspension into each well of the 6-well dish directly on top of the virus. Swirl gently to mix and place...

..., but do not cut within your insert Are in the desired location in your recipient plasmid (usually in ...possible to use a single enzyme, but this will require phosphatase treatment of your recipient plasmid... fear. You have other options, such as: Adding desired restriction sites to flank your insert : You can...restriction enzymes that cut within your insert. Adding desired restriction sites to your recipient plasmid : You...

... per well. Allow the HeLa cells to grow to the desired density before labeling. Section 2: Fixing and ... container. Dilute the primary antibody to the desired concentration in antibody dilution buffer. Pro-...fluorescently-labeled secondary antibody to the desired concentration in antibody dilution buffer. Pro-...

... science-fiction levels of detail. You can take entire courses on microscopy and still have more to learn...nosepiece so that the lowest power objective is directly over the stage. It is best practice to start with...attached to them that allow you to capture images directly to a computer, but many microscopes do not and...

...Introduction Many molecular biology techniques require highly purified and concentrated plasmid DNA. This... volume of bacteria to grow (low copy plasmids require larger cultures). Centrifuge the culture to pellet...proceeding with DNA preparation. Pro-Tip If your entire overnight culture cannot fit into a single centrifuge...

...-agar 1 L Sterile H 2 O Sterile plates of your desired size - we usually use 60 mm x 15 mm plates which...next to the flame and begin pouring. Measure your desired amount of agar with a pipete for the first plate...particular plate. For the remainder of the plates, pour directly from the bottle. Pro-Tips Be sure to swirl your...

...that: Do not cut within your insert. Are in the desired location in your recipient plasmid (usually in ...amplified (the ORF in this case), not the Tm of the entire primer. If you are amplifying from a plasmid or...plenty of starting material. We recommend using your entire PCR reaction and 1μg of recipient plasmid. It is...

...Spectrophotometer to see if the sample has reached the desired concentration. If the sample concentration is still...volume of the sample is reduced enough to reach the desired concentration. Pro-Tip Periodically check the concentration...Spectrophotometer to see if the sample has reached the desired concentration. Gently transfer the sample from ...

...generally considered biosafety level 1 but may require BSL-2 handling depending on the insert. Please ...liquid up and down 10–20 times. Gently cover the entire dilution plate with Microseal adhesive seal - do...droplets are not disrupted, insert the pipette tips directly in the center of the well and tilt to a 45° angle...

...bacterial colonies. Equipment Sterile toothpicks or wire loop Bunsen burner (or other small flame source)... top of the glycerol stock. Pro-Tip If you use a wire loop you can sterilize it by passing it through ...

...and with a clean, sterile razor blade, slice the desired DNA fragment from the gel. Notes: To protect the...with the gel fragment. The weight of the gel is directly proportional to its liquid volume and this is ...

...you can design a set of oligos containing your desired restriction sites and add them to your existing...overlapping oligos that once annealed can be cloned directly into the overhangs generated by restriction digest...

...Set up your water bath so that it will reach the desired temperature by the time you need it for your experiment...water bath to prevent evaporation and maintain the desired temperature. This also helps the water bath heat...

...cells Antibody Validation Using the Indirect ELISA Method Run an indirect ELISA against a purified antigen...

... likely to ligate to itself rather than to the desired insert. If you are in this situation, it is important...Additional controls are encouraged, but may only be required for troubleshooting failed ligations. The following...

...maximum possible setting on the pipette, set the desired volume of the liquid on the pipette. Depending ... you can slowly release the plunger. Remove the entire pipette from the container making sure not to touch...

...to the template DNA and the Taq polymerase, PCR requires free nucleotides [dNTPs; adenine (A), cytosine... thymine (T)] in an equal molar ratio. It also requires two unique single stranded DNA oligonucleotide...

...Last Update: February 13, 2019 Estimate of time required: ~3 h Workflow Timeline Plate set-up: 2 h qPCR...enough master mix for all samples). Each sample requires 15 μL of master mix. Pro-Tips Use a "Universal...